LevelOne GEP-2671 Manual do Utilizador Página 129
- Página / 270
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
115
Primary Power Supply [W] :
The switch can have PoE power supplies. It is used as power source, For being able to
determine the amount of power the PD may use, it must be defined what amount of power
the power sources can deliver.
Ethernet Port Configuration
Port :
This is the logical port number for this row.
PoE State:
The PoE Mode represents the PoE operating mode for the port.
Disabled: PoE disabled for the port.
Enabled : Enables PoE IEEE 802.3af/at
Priority :
The Priority represents the ports priority. There are three levels of power priority named
Low, High and Critical.
The priority is used in the case where the remote devices requires more power than the
power supply can deliver. In this case the port with the lowest priority will be turn off starting
from the port with the highest port number.
Maximum Power :
The Maximum Power value contains a numerical value that indicates the maximum power
in watts that can be delivered to a remote device.
NOTE: If you want to set the Port support IEEE802.3at then you can
set the Maximum allowed value is 30W.
Buttons:
Save – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved values.
- GEP-2671 / GEP-2672 1
- INTRODUCTION 11
- Initial 12
- Configuration 12
- System Configuration 18
- 2-1.2 Configuration 20
- 2-1.3 CPU Load 21
- 2-2 Time 22
- 2-2.2 NTP 24
- 2-3.1 Users 25
- 2-3.2 Privitege Level 27
- 2-4.1 IPV4 29
- 2-4.2 IPV6 31
- 2-5 Syslog 32
- 2-5.2 Log 33
- 2-5.3 Detailed Log 34
- 2-6 SNMP 35
- 2-6.2 Communities 36
- 2-6.3 Users 37
- 2-6.4 Groups 39
- 2-6.5 Views 40
- 2-6.6 Access 41
- 2-6.7 Tarp 43
- Configuration 45
- 3-1.2 Port Description 47
- 3-1.3 Traffic Overview 48
- 3-1.4 Detailed Statistics 49
- Receive Error Counters 50
- Transmit Error Counters 50
- 3-1.5 Qos Statistics 51
- 3-1.6 SFP Information 52
- 3-1.7 EEE 54
- 3-2 ACL 56
- 3-2.2 Rate Limiters 58
- 3-2.3 Access Control List 59
- 3-2.4 ACL Status 62
- 3-3 Aggregation 64
- 3-3.2 LACP 66
- 3-4 Spanning Tree 71
- Basic Settings 72
- Advanced Settings 72
- 2-4.2 MSTI Mapping 74
- MSTI Mapping 75
- 3-4.3 MSTI Priorities 76
- 3-4.4 CIST Ports 77
- 3-4.5 MSTI Ports 78
- 3-4.6 Bridge Status 81
- 3-4.7 Port Status 82
- 3-4.8 Port Statistics 83
- 3-5 IGMP Snooping 84
- Parameter description: 86
- 3-5.3 Port Group Filtering 88
- 3-5.4 Status 90
- 3-5.5 Group Infermation 92
- IGMP Group Table Columns 92
- 3-6 MLD Snooping 95
- 3-6.2 VLAN Configuration 98
- 3-6.3 Port Group Filtering 100
- Web Interface 100
- 3-6.4 Status 101
- 3-6.5 Group Information 103
- 3-6.6 IPv6 SSM Information 105
- 3-7 MVR 106
- MVR Group Table Columns 108
- 3-7.3 Statistics 109
- 3-8 LLDP 110
- LLDP Parameters 111
- LLDP Port Configuration 111
- 3-8.2 LLDP Neighbours 113
- Fast start repeat count 115
- Coordinates Location 116
- Civic Address Location 116
- Policies 118
- 3-8.4 LLDP-MED Neighbours 121
- 3-8.5 EEE 124
- Global Counters 126
- Local Counters 126
- 3- 9.1 Configuration 128
- Ethernet Port Configuration 129
- 3-9.2 Status 130
- 3- 10 Filtering Data Base 131
- MAC Table Learning 132
- MAC Table Columns 133
- 3-11 VLAN 134
- 3-11.2 Ports 136
- Web Interface 136
- 3-11.4 Port Status 139
- 3-11.5 Private VLANs 141
- 3-11.5.2 Port Isolation 142
- 3-11.6 MAC-based VLAN 143
- 3-11.6.1 Configuration 143
- Web Interface 143
- 3-11.6.2 Status 145
- 3-11.7 Protocol -based VLAN 146
- 3-11.7.1 Protocol to Group 146
- 3-11.7.2 Group to VLAN 148
- Auto-refresh : 149
- 3-12 Voice VLAN 150
- 3-12.2 OUI 152
- 3-13 GARP 153
- 3-13.2 Statistics 155
- 3-14 GVRP 156
- 3-14.2 Statistics 158
- 3-15 QoS 159
- 3-15.2 Port Policing 161
- 3-15.3 Port Scheduler 163
- 3-15.4 Port Shaping 166
- 3-15.5 Port Tag Remarking 169
- Buttons: 170
- 3-15.6 Port DSCP 171
- 3-15.7 DSCP-Based QoS 173
- 3-15.8 DSCP Translation 175
- 3-15.9 DSCP Classification 177
- : Edits the QCE 179
- 3-15.11 QCL Status 181
- 3-15.12 Storm Control 183
- 3-16 s-Flow Agent 184
- 3-16.2 Sampler 186
- 3-17 Loop Protection 188
- 3-17.2 Status 190
- 3-18 Single IP 192
- 3-18.2 Information 193
- 3-20 Mirroring 196
- Mirror Port Configuration 197
- 3-21 Trap Event Severity 198
- 3-23 UPnP 200
- Security 201
- 4-1.2 Static Table 203
- 4-1.3 Dynamic Table 204
- 4-2 ARP Inspection 205
- 4-2.2 Static Table 207
- 4-2.3 Dynamic Table 208
- 4-3 DHCP Snooping 209
- DHCP Snooping Configuration 209
- 4-3.2 Statistics 211
- 4-4 DHCP Relay 213
- 4-4.2 Statistics 215
- Client Statistics 215
- 4-5 NAS 217
- 4-5.2 Switch Status 224
- 4-5.3 Port Status 226
- Port State 226
- Port Counters 226
- Selected Counters 227
- Attached MAC Addresses 227
- VLAN ID 227
- 4-6 AAA 229
- 1. Check “Enabled” 229
- 4-6.2 Radius Overview 233
- RADIUS Accounting Servers 233
- 4-6.3 Radius Details 235
- 4-7 Port Security 236
- Port Configuration 237
- 4-7.2 Switch Status 239
- 4-7.3 Port Status 241
- 4-8 Access Management 242
- 4-8.2 Statistics 244
- 4-9 SSH 245
- 4-10 HTTPs 246
- 4-11 Auth Method 247
- Maintenance 248
- 5-2.1 Firmware Upgrade 249
- 5-2.2 Firmware Selection 250
- 5-3 Save / Restore 252
- 5-4.1 Export Config 254
- 5-4.2 Import Config 255
- 5-5 Diagnostics 256
- 5-5.2 Ping6 257
- 5-5.3 VeriPHY 258
Manuais e produtos relacionados com Comutadores de rede LevelOne GEP-2671
(17 páginas)
(2 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais