Levelone FPS-1032 Manual do Utilizador

1 LevelOne User Manual FPS-1032 USB Print Server Ver. 1.1

10 NT/2000/XP/2003/Vista/7 management of print server, include alert and consumables of multiple printers- anywhere on your LAN Internet Printing Pro

11 3. Software Installation The PSAdmin is a proprietary

12 3. Choose Setup Wizard to install the print server and configure the connected printer. Note: The setup CD will install the print server’s dri

13

14 6. On the Change Settings screen, select No or Yes: Click No if you want the print server to keep using the default IP address and keep the de

15 Select Add New Printer if the print server is connecte

16 8. Click Add New Printer to launch Windows Add Printer Wizard. 9. Click Next and select Local Printer, make sure the Automatically detect and

17 10. Make sure the Use the following port radio-button

18 12. If you already have the printer’s driver installed, you will be asked whether to keep it or to replace it. Click Next. Supply a name for the

19 16. Right-click, select Properties -> Ports and

2  The LevelOne Support Team can not support questions or compatibility issues with the following operating systems: Windows NT/95/98/98se/Me

20 17. Go to General; click Print Test Page to verify the configuration. 18. Done. Note: If you want to install more print servers, start setup w

21 Version: The firmware version of the print server. St

22 4 (Optional) In the Subnet Mask option, type the Subnet Mask your LAN or network segment is currently configured to use. 5 (Optional) In the G

23 5. Type in a Print Queue Names. Note: Each print que

24 6. (Optional) In Bindery Settings, Select NetWare file server(s) that print server can do Bindery mode. 7. (Optional) In NDS Settings, Select N

25 Subnet Mask: This option shows the print server’s cur

26 Refresh 1. Click Reset button just like a picture ＜ ＞. 2. Refresh searches the network for all attached print server(s). Note: Configure t

27 Procedure: 1. Click Start, point to Settings, an

28 4. Internet Printer Connection and HP Web JetAdmin IPP Overview Print server(s) support the Internet Printing Protocol (IPP). Using the appropri

29 6.In URL’s box, input print server’s IP address, for

3 TABLE OF CONTENTS COPYRIGHT ...

30 9.If you want your Windows-based programs to use this printer as the default printer, please select “Yes”, and Click Next. It will appear as follo

31 Installing HP Web JetAdmin Before installing the HP W

32 5. Configuration from Embedded Web Server Overview The Print Server contains an embedded web server that can be accessed through a supported we

33 Print Server Name: This option allows you to view de

34 Printer Status 1. Click Status, it then appears the sub-menu. 2. Click Printer, it then as shown in the following picture. Manufacturer: This

35 Use DHCP/BOOTP: This option allows you to view DHCP/

36 General Settings: Print Server Name: This option allows you to view print server’s name would be configured by PSAdmin utility. Polling Time:

37 AppleTalk Status 1. Click Status, it then appears th

38 SNMP Communities: This option allows you to view SNMP communities from the print server. There are two communities that control message from the

39 Workgroup Name: This option allows you to view the

4 POWER RELATED PROBLEMS ...

40 Email Alert: This option allows you to Enable/Disable the Email Alert support. SMTP Server IP Address: This option allows you to input the IP a

41 ˙User Name: You must be input the default administra

42 IP Address: This option allows you to input IP address from the print server. The IP address must meet the IP addressing requirements of the netwo

43 Print Server Name: This option allows you to input p

44 Installing Print Server on NetWare 4.x/5.x Due to its architecture and functionality, the print server must work under NetWare 4.x/5.x NDS Binde

45 Note: Please refer to NetWare’s Print Server/Services

46 <ATALK_PS>-xxxxxx-1, where xxxxxx represents the last six digits of the device’s Node ID. For example: ATALK_PS-40EEED-1. You may also chang

47 TCP/IP networks use a standard management protocol cal

48 Enables or disables the function of sending SNMP Authentication Failure trap message to the network administrator, if the community name within a

49 SMB Setup The print server supports the SMB (Server M

5 Trademarks NetWare is a registered trademark of Novell

50 6. Network Print Monitor Preparation The print server supports TCP/IP, IPX/SPX and NetBEUI protocols under Windows 95/98/ME/NT4/2000, XP 32bi

51 TCP/IP Protocol Installation 1. Click Start, point to

52 NetBEUI Protocol Installation 1. Click Start, point to Settings, and select Control Panel. 2. Double click the Network icon. 3. If the NetBEU

53 10. A message reading, “After your printer is installe

54  By default, the computer will first search for the print server(s) on the network by using the IPX/SPX protocol.  If the IPX/SPX protocol is

55 7. TCP/IP LPR Port Printing Installation Basic TCP/

56 5. From the Printer Ports box as shown in the following picture, select the LPR Port. 6. The Add LPR compatible printers box will then appear

57 Windows 2000/XP/2003/Vista/7 Standard TCP/IP Port Prin

58 6. In the Add Standard TCP/IP Printer Port Wizard box as shown in the following picture, Select Custom, Click Settings button, and click Next.

59 9. Click Finish. 10. Select the appropriate printe

6 1. Introduction Product Overview The external print servers enhance capability by letting you place your printers at convenient locations directly

60 UNIX Installation After the static IP address is assigned, the Print Server is ready to be configured. For some UNIX/Linux systems, we include th

61 Redhat Linux 9(Fedora) The Print Server can work unde

62 7. Click Forward button.

63 8. In the Name field, type a user-defined name, click

64 14. Choose the model of printer and click Forward. 15. Done.

65 8. Upgrading Print Server Overview Upgrading print se

66 3. Wait for the transfer successful message. 4. Done. Upgrading the print server from UNIX (Through TCP/IP) 1. Log in as root 2. Ensure b

67 4. Click Browse… and select the firmware file. 5.

68 9. Troubleshooting General Troubleshooting Overview The most common problems, which cause the print server to perform improperly, are covered in

69 check the cable connection. If the pins are damaged, c

7 LED Indicators LED State Indication Status Blinking for

70 Moving the print server to A New Segment If the print server is moved from one network segment to another after the initial installation, through

71 Moving Your Computer to A New Segment If you are usi

72 B. The print server's IP address is duplicated or is as same as another computer's IP address on the network. If t

73 6. In your editor, modify "BoxIPAddress" fi

74 Appendix SMB Printing with Windows XP 1. Enable the SMB settings from the print server’s WEB configuration. Assume your computers use the “WORK

75 3. Double click it again. 4. Now you have to ins

76 5. Choose it from the “Add Printer Wizard”. 6. Install printer successfully.

77 7. Now, you can find your printer’s icon and you ca

78 Reset Button Reboot the Print server: 1. Verify the power of print server is turned on. 2. Press the reset button once, and then release it. WA

79 Frequently Asked Questions Question A Print jobs ar

8 Wall-mount Information Note: We are not responsible for damages incurred by insecure wall-mounting hardware. Network Environment Wired Network w

80 Question D The Status LED light keeps blinking after POST. Possible explanation and solution The last upgrade process was not completed. The p

81 Additional Installation Instructions Panasonic KX-P61

9 2. Print Server Installation Preparation To meet users